SAMBA server on Zidoo 1000 pro very slow

Finally you've solved it

 

Great you solved your problem, whats your copying speed now?

Best buy I did for only 9.95 euro.

BLEIL Kabeltester RJ45 kopen bij HORNBACH

 

Yes. Solved thanks to a cable tester and iperf3.exe!! My speed is now about 950 Mbits /sec!

 

Its was a pain in the ass to make new connectors on the cable. I have ordered new connectors at Ali Express. Do you know these? I hope these will connect more easy next time.
https://nl.aliexpress.com/item/4000351501951.html?spm=a2g0s.9042311.0.0.394f4c4dSu5x5Y

 

I've tried it onced and the cable didn't work.

 

Not sure exactly but when I wired up my son's Home Cinema setup before Christmas, we managed to successfully put Rj45 connectors on to the ends of the Cat7 cables by ripping off the metal sheathing, thus downgrading them to CAT6 cables.

 

As long as you use decent quality plugs, have a decent ratchet crimper and make sure you get the order of the cores correct it's quite easy but there is a bit of a knack to it.

 

And it's always handy to have a cheat sheet handy - this is mine (Assumes 568B, which most are)

 

Hello every body,

I've the same problem-> transfert file to my internal drive of the Zidoo is 300Mbits Maximum.

I've try all you suggested here. But the same result each time 290-300 Mbits.

I've changed 3 times the cable try with 2 different routers nothing change.

The only thing I cannot do is to make a manufactory reset because I dont know how to make a recovery file of my system.

Zidoo Ethernet is 1GB and Pc is 1GB Connection

Regards

Fred



-----------------------------------------------------------
Accepted connection from 192.168.0.98, port 33192
[ 5] local 192.168.0.109 port 5201 connected to 192.168.0.98 port 33194
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-1.00 sec 31.8 MBytes 267 Mbits/sec
[ 5] 1.00-2.00 sec 33.9 MBytes 285 Mbits/sec
[ 5] 2.00-3.00 sec 35.3 MBytes 296 Mbits/sec
[ 5] 3.00-4.00 sec 34.3 MBytes 288 Mbits/sec
[ 5] 4.00-5.00 sec 34.6 MBytes 291 Mbits/sec
[ 5] 5.00-6.00 sec 35.0 MBytes 294 Mbits/sec
[ 5] 6.00-7.00 sec 34.9 MBytes 292 Mbits/sec
[ 5] 7.00-8.00 sec 34.8 MBytes 292 Mbits/sec
[ 5] 8.00-9.00 sec 34.3 MBytes 288 Mbits/sec
[ 5] 9.00-10.00 sec 33.7 MBytes 283 Mbits/sec
[ 5] 10.00-10.04 sec 1.38 MBytes 270 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth
[ 5] 0.00-10.04 sec 0.00 Bytes 0.00 bits/sec sender
[ 5] 0.00-10.04 sec 344 MBytes 287 Mbits/sec receiver
-----------------------------------------------------------

 

Would you please try to copy some bigger file, like 1Gb from your PC to Zidoo and then from Zidoo to PC in Windows environment and watch little popup window where transfer rate will be shown in MB/s which is not the sam as Mbps and then calculate your outcome. I use CAT 7 cable, 10m long and TP Link switch and my speeds are arround 900-950 or 80-90 MB/s mbps. It could change your situation if you put static IP also.

 

Hello,

Thx for the response.

This is the speed a 9Gb file to the intern Hdd in the Zidoo.

Very Slow ->

23.6 Mégaoctets = 188.8 Mégabits




The same to my NAS cable routeur same

 

Would you try to set Static IP in Zidoo ethernet using Settings/Network/Ethernet then turn off Auto (DHCP) and fill all other fields with your network data from picture above and press button Connect. For instance your IP Address is 192.168.98, Gateway should be 192.168.0.1, Subnet mask is 255.255.255.0 and use DNS address 109.88.203.3

It is very important that you setup Static IP addresses in all of your equipment like PC or servers where network communication is performing. After that, turn off all your equipment (power off completely) and power them on, one by one, starting with router.

All details I saw on your picture above, you can use other Static IP address in accordance with your needs.

 

Hi,

I've made what you said.

Change ip and DNS

Pc network Ip fixed and Zidoo Ip fixed

Same result. Very Slow.

Hard reset of the Zidoo ?

F.

 

Before hard reset, look for newest firmware first and try to use CAT5e cable or better.

 

Hi,

Last week I've Firmware V6.4.42 and updated to v6.4.62 beta No difference !
All my cables are CAT8 2M long 40Gbps 2000Mhz

I'll do a reset and post a reply

Thx for your time !

F.

 

Have you tried turning off small buffering option in Settings => Realtek Developer Options?

 

Hello, not for the moment. I'll try that.

Not found this settings.

Go to infomation > Realtek but only Audio and Video settings.

 

What player do you have?

 

Hello,

Zidoo Z1000Pro.