1: Download the flash package (attached the driver) [Download] Unzip the burning tool, click and open this tool 2: Lay in the downloaded flash package of “ZIDOO_X6 Pro_v1.x.xx.img” Download ZIDOO_X6 Pro_v1.0.19.img (742 MB) http://www.mediafire.com/download/l0m9ao84j84l10l/ZIDOO_X6_Pro_v1.0.19.img 3: Using the double port USB cable (as show in the Figure), one connects to USB ⑦USB/OTG, the other connects to PC. Press reset button, (If used for the first time, will show the drive installation; if failed, please make it with manual installation ) After finishing installation, it will show related connection “Port”, then click “ Run” and it will burn the firmware automatically. The firmware is under burning, the icon that is in the upper right corner of will turn blue, and there is a prompt “Download Firmware..” on the middle port. The firmware has been burning, it will show the ID and Time about finishing burning on the right. Part TWO: The reference of local OTA upgrade process: ZIDOO_X9（http://blog.zidoo.tv/2015/02/how-to-upgrade-the-zidoo-x9-firmware/） Part THREE: Online update, to download the latest firmware version, which is similar to the local OTA upgrade. Notices: 1. Do not disconnect USB cable during flashing (It will take about 1min and 20s to flash); if over 2min, you can choose to flash again. 2. It will be slower to turn on for the first time after flashing, please wait with your patience; if can not enter system, you can choose to flash again to recover.
Can some of the moderators can point why a Firmware version V1.0.19 is available on this tutorial and is not available for public Release ?
Hello, I've updated firmware with "local OTA upgrade process (Part two)", much easier then the process you described here, to 1.0.23 without no issue. But when some updated FW (1.0.22 or .23) will be delivered via OTA ? Thanks
in my x6 pro the procedure don't work. Factory tool don't see the port when i attached the usb cable. i have manual installed a driver in to the driver directory
do you press the button until you in sert the usb cable? do you insert the right usb port? if do that, the windows will read the rk device insert.
I have tried in various ways. Start FactoryTool , load the ROM and start the procedure . insert the cable into the USB port of my computer , I hold down the reset button until I insert the cable into the USB otg port X6 pro . Or , insert the PC cable , insert the cable nell'x6 pro usb otg and I press the reset button.
1. Unplug Zidoo Power Supply Unit (PSU) and put it somewhere. Do not use it. 2. Install drivers from DriverAssitant v4.3 on your PC 3. Launch FactoryTool v1.39 and load the firmware image file. 4. Take USB 2.0 Male to Male cable and plug it in PC USB port. 5. Using pinpoint push and hold "Reset" button in Zidoo box. While holding the button plug another end of the USB cable to USB/OTG port of the box. You will see "Loader" name appeared in "Device Type" column of the FactoryTool. 6. After this just click on "Start" button and wait for the firmware flash to complete.
Hmmm, there might be false positive virus alert of DriverAssitant_v4.3.zip -file? Two antiviruses alerted, Bkav and Ikarus (never heard of these earlier)? Please see the latest VirusTotal scan report.
yes you can,, beginning with this version ...Download ZIDOO_X6 Pro_v1.0.19.img (742 MB) after step by step upgrade every FW Version...
Can someone upload the img file to something different than mediafire? And post a link here? I'm not able to download the file from mediafire, and i need it to downgrade the firmware.
